Shopping Cart - $0.00

You have no items in your shopping cart.

Drill Doctor 750X
Drill Doctor 750X
Drill Doctor 750X Drill Doctor 750X Drill Doctor 750X Drill Doctor 750X Drill Doctor 750X

Drill Doctor 750X

DD750X User Guide

Availability: In stock

$139.95
Item Number: DD750X

The top of the line 750X sharpens drill bits from 3/32” to 3/4”. Point angles can be set anywhere from 115 to 140 degrees. Adjustable material take-off allows you to adjust the amount of material removed during sharpening - extending the life of your bits. The 750X is built to stand up to professional use.

Designed, engineered, and assembled in the U.S.

Use our Where To Buy page to find local and online retailers.

Drill Doctor 750X

  • Sharpens standard twist and masonry bits from 3/32" to 3/4"
  • Custom point angle sharpening: set any angle from 115 to 140 degrees
  • Adjustable material take-off: Allows user to change the amount of material removed during sharpening to further extend the life of your bits
  • Cast aluminum point angle shuttle for added durability
  • Sharpens Carbide, Cobalt, High-Speed Steel, Black Oxide, TiN-Coated, twist and Masonry bits
  • Longer chuck jaws hold bits more precisely, and jaw guides eliminate jaw twisting on small bits
  • Able to create and sharpen split point bits.
  • "Push to Stop" drill point splitting port: Will not allow you to over split the bit point
  • Permanent magnet motor produces consistent power, regardless of speed or load
  • Easy to replace diamond sharpening wheel
  • 6 foot power cord
  • Includes storage bag


What's in the box:

  • 750X Drill Bit Sharpener
  • 3/4" chuck (for bits from 3/32” to 3/4”)
  • 180 grit diamond sharpening wheel (pre-installed)
  • 750X User Guide
  • Carrying/Storage bag
  • Wheel hub wrench (for changing or replacing diamond sharpening wheels)


Optional Accessories:



Warranty

A 3-Year Warranty protects every Drill Doctor bit sharpener against defects due to workmanship or design; abrasives excluded. Warranty does not cover industrial or commercial use.

NOTE: Using a 115V machine in a location with 230V power sources voids the warranty. For use outside North America, visit our "Where To Buy" page to find a distributor in your country or region.


Customer Reviews

Items 28 to 30 of 44 total

Page:
  1. 1
  2. ...
  3. 8
  4. 9
  5. 10
  6. 11
  7. 12
  8. ...
  9. 15
I'm a DIY Review by Hobbyist
Price
Value
Quality
I'm a DIY and my 750X has been great for my needs. It does take some time to sharpen the larger bits but the convenience of having it available is great. The cost of a new bit may be under ten dollars but the time and expense of going to the local box store and buying it is prohibitive. (Posted on 7/25/15)
Homeowner grade sharpener. Way too slow. Review by Metal Man
Quality
Price
Value
If you are a home hobbyist where time does not equal money this sharpener would be a reasonable addition to your workshop. For a business or shop it is not practical. It is extremely slow to sharpen a drill bit. Way too much turning required (20 turns minimum for a 3/8" bit and at least 50-60 for a 1/2" bit). The alignment process with the two spring loaded flute tabs seems to struggle with bits that you have previously split point. The company offers two wheel selections. It comes with the finer wheel. This coarseness of grit produces a reasonably sharp bit but it takes forever. The coarse wheel is little bit faster but does not offer a nice finished cutting edge. Changing wheels is just another time consuming step. If you are on the clock you can buy bits cheaper than sharpening them with this sharpener (750X). If it takes 10 minutes to sharpen a 1/2 bit (even at a low shop rate of $60/hr.... you can buy a reasonable quality 1/2" bit for under $10). The wrist rotating motion, with hand tense and pressure maintained to keep the chucks lobe on the cam post, does produce some discomfort after doing a few bits. My replacement sharpener cost a fair bit more than the 750X and sharpens a bit in under 1 min and is accurate to 0.002mm. So in conclusion, the Drill Doctor sharpener is an OK homeowner sharpener where you might sharpen a couple of bits a week. But if you sharpen bits daily, and time is money, it will end up costing you more money than it saves.

Drill Doctor response: We are glad you found a sharpener for your business that will save you time/money. (We hope it's a Darex machine!) The Drill Doctor models are indeed designed for DIY workshops, hobbyists and professionals that have low volume drill sharpening needs. Large bits do take longer to sharpen as more material needs to be removed, and our industrial line (Darex) is designed specifically for professionals with sharpening requirements such as yours. Thank you for your review, we appreciate customer feedback. (Posted on 4/13/15)
Great product, love it! 750x Review by The 35yr Machinist
Price
Value
Quality
Wanted a black diamond, couldn`t afford it, this works great for the money. Got it today, sharpened all my stub drills had for 30yrs. 3 indexes worth. Its already paid for itself in 1 day! I have all American Steel. Diamond wheel still in good shape, after 100 or more. Its all in the touch boys like a good woman, don`t be stupid , buy 1 of these and SAVE money! Don`t buy China crap. Buy AMERICAN! (Posted on 4/4/15)

Items 28 to 30 of 44 total

Page:
  1. 1
  2. ...
  3. 8
  4. 9
  5. 10
  6. 11
  7. 12
  8. ...
  9. 15

Write Your Own Review

You're reviewing: Drill Doctor 750X

How do you rate this product? *

  Your rate 1 star 2 stars 3 stars 4 stars 5 stars
Price
Value
Quality